How To Make Dowel Joints

How to make a dowel articulation

This diy article is about how to brand a dowel joint. Mostly speaking, wood pegs are used when making furniture or when joining together tightly several pieces of woods. In nearly cases it won't be enough to fasten the wood joint of the wooden pieces by using mucilage, just you besides take to make a dowel joint using woods pegs. This techniques is quite old only very efficient, as it creates a secured joint between two or more forest parts.

Usually, you as well have to employ gum around the dowel pins, as information technology volition enhance the strength of the wood articulation, particularly if you lock the components together with several clamps. Later the glue has dried out, the dowel articulation will exist even stronger than a regular piece of wood, provided you employ the proper techniques and tools. See all my Premium Plans in the Store.

Materials

Woods dowels / dowel pegs
Woods mucilage

Tools

Level, rubber hammer, measuring tape
Clamps, drill machinery and bits
Metallic dowel points
Framing foursquare, carpenter pencil

Tips

Read prophylactic and disclaimer pages
Use a good drill machine with torque control
Use metal dowel points, every bit to brand a proper dowel joint
The best choice is to employ a dowel jig
Leave at least 1/2" from the edge or corner of the wooden function, when drilling holes

Drilling holes for dowel joint

Marking the holes for dowel pegs

If y'all don't have a dowel jig (which is the all-time option when making a dowel articulation), you have to use a L-square to marker the spot where yous are going to drill several holes. Consequently, beginning draw a line over the median of the wooden post. Next, use the l-square or a record measure to mark the exact spots where you are going to dill the holes (in our case the intersection of the lines).

Drill bit for installing dowel pins

In gild to get the job done in a professional manner, we have to use wood dowels and a sharp drill bit. Almost dowel pegs range from 1/2" up to 1/iv", according to the blazon of your project. If you desire to joint together furniture boards, y'all accept to use in most cases one/4" dowel pegs, as for bigger parts yous can install 1/2" wood dowels.

Drilling holes in the wood joint parts

Drilling holes in the forest joint parts

Next, utilise a skilful drill machinery with torque control to drill several holes. If the pieces of wood y'all want to lock together are no larger than 3-4", then 2 wood plugs will practice only fine.

Holes for installing dowel pegs

When drilling the holes make sure you hold the drill mechanism perpendicular on the wood lath's surface. Although it might look difficult to drill the holes without a dowel jig, we assure you can do information technology with little practice.

Drilling the mating holes in the other forest part

Using metal dowel points

Next, we have to drill the holes in the other half of the wood joint. Consequently, nosotros have to use metallic dowel points, equally to make certain the two components are aligned properly. Put the dowel point in the drilled holes, making sure they are ready accurately into position.

Marking the mating holes in the second component

Next, place the second component over the first piece of forest, making sure their edges are perfectly aligned. If you are joining two small pieces, then y'all could set the components together beside a directly wall or a piece of work demote.

Drilling holes with brad-point drill bit

Drilling holes with brad-signal drill bit

Adjacent, nosotros have to drill holes in the second piece of woods, as to bring together together the two halves using dowels. As to make sure the two parts volition friction match each other, you lot accept to drill holes over the marks, using the same technique described higher up.

Installing dowel pegs

Side by side, as our projection regardinghow to join woods with dowels is most done, we have to install the dowel pegs. Consequently, pour a little wood glue in the holes and them tap firmly the wood dowels until you accept inserted half of them.

Fastening wood joint with dowels

Final but not to the lowest degree, we have fastened the dowel articulation past locking together the 2 wood pieces. Earlier tapping the tiptop part with a safe mallet, you have to brand sure the components are aligned properly. Next, utilize more mucilage in the holes of the other half, before locking them firmly.

Cheers for reading our article on how to brand a dowel joint, and nosotros recommend you to check out the remainder of our projects. Delight SHARE and LIKE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the beginning that gets our latest projects.